Look at the operation and maintenance of the crusher from a small label

Customers who recently purchased our small crusher will find that a new small label has appeared on our crusher lid. This label contains three patterns. Each pattern allows us to pass a layer of information. Today we pass the This small new label allows you to explain the problems that should be noticed during the use of a small crusher!

First of all, we look at the first pattern. There is a hand and a dangerous cue in the pattern. The reason why this pattern is placed in the first place is inseparable from the principle of “safety first” that Ben Chen has always insisted on. Small-sized crushers are all ultra-high-speed motors with a speed of 25,000r/min. This rotation speed has even exceeded the helicopter's propeller rotation speed. Such high speed brings not only improvement in fineness, but also improvement in crushing efficiency. What is important is a safety issue that must be taken seriously. If a small high-speed accident occurs at such a high speed, the outcome will be unpredictable. In the process of production, in the process of sales, in the process of use, the first concept of employees of this Chen is safety, for the safety of customers for their own safety, so the small grinder must comply with the instructions in the use of Operation, in any case open the machine cover must first cut off the power, so as to ensure maximum safety of life, there is the machine is not allowed to open the lid during the crushing process, this is a very very dangerous operation, not only the splash of material will Injury to humans, accidentally touching other parts of the body. Shattered blade. Those who suffer from disability are at risk. Therefore, any operator must keep this in mind. Operate strictly in accordance with the operating instructions. Safety is the top priority. .

The second pattern many people have doubts, your smash is not stainless steel, why not wash it with water. Here we focus on explaining this issue. In fact, the main meaning of this icon is to crush the interior of the ban on water washing, that is, to prohibit the injection of any liquid into the comminuting chamber. This is mainly to prevent water or other liquid from entering the motor through the rotor shaft. If the liquid enters the motor, It is very easy to burn when the motor is started again. Followed by a small grinder in addition to the motor and some electrical control components are also not allowed to contact the liquid, otherwise there will be leakage, failure and other consequences, so when cleaning the small grinder is not allowed to crush the chamber water, wet rags can be , However, after the cleaning is completed, the machine should be placed in a ventilated place for drying to prevent the internal or surface of the machine from being exposed to moisture.

The third icon mainly reminds us of the security risks caused by the warming of the machine surface. As the small-sized crusher uses an ultra-high-speed motor, the blade collides with the crushing material during the crushing process, and the friction generates a large amount of heat. Since the small crusher uses a closed crushing chamber, the generated heat cannot be dissipated directly into the air, resulting in crushing. Room temperature increase grinder appearance hot, this phenomenon is not a problem with the quality of the mill (but a lot of poor crusher motor housing will be very hot and this is the result of poor motor quality), mainly by the small grinder crushing principle and This phenomenon is caused by the influence of its own structure. For safe small crusher after repeated use many times if the crushing outdoor table temperature is too high, we recommend that you can properly stop for a few minutes, after the standby temperature drops and then use. If there is a significant increase in the temperature of the motor housing, there are two reasons. One is that the machine will not be able to discharge the heat generated by itself for a long time. The second is that the crusher rotor uses aluminum wire material (or copper clad aluminum) to cause the heat of the machine itself. Relatively high. The second reason is the phenomenon that most of the inferior shredders are currently appearing in the market. In order to eliminate this phenomenon from the beginning of construction, we have always adopted the pure copper wire motor of domestic famous brands. This is a product. The pursuit of quality is a promise made for the safety and security of our customers.

A small label represents the promotion of a business service. As one of the few enterprises that consistently adheres to the finest small crushing machines, Benchen regards user safety as the first priority and regards product quality as the first priority in corporate life. We will continue to improve and upgrade our products to provide better products for our customers.